[1]刘超,仇成华,徐达强.两段式拉力螺钉的滑丝率和加压力研究[J].中医正骨,2025,37(02):28-33.
　LIU Chao,QIU Chenghua,XU Daqiang.The thread stripping rate and pressurization force of a two-segmental lag screw:a biomechanical study[J].The Journal of Traditional Chinese Orthopedics and Traumatology,2025,37(02):28-33.
点击复制

两段式拉力螺钉的滑丝率和加压力研究()
分享到：

《中医正骨》[ISSN:1001-6015/CN:41-1162/R]

卷:
第37卷
期数:
2025年02期
页码:
28-33
栏目:
基础研究
出版日期:
2025-02-20

文章信息/Info

Title:
The thread stripping rate and pressurization force of a two-segmental lag screw:a biomechanical study
作者:
刘超1; 仇成华2; 徐达强2
(1.河南省洛阳正骨医院/河南省骨科医院,河南 洛阳 471002; 2.盐城市第三人民医院,江苏 盐城 224008)
Author(s):
LIU Chao1; QIU Chenghua2; XU Daqiang2
1.Luoyang Orthopedic-Traumatological Hospital,Luoyang 471002,Henan,China 2.Yancheng Third People's Hospital,Yancheng 224008,Jiangsu,China
关键词:
骨螺丝;  骨质疏松性骨折;  松质骨;  滑丝;  加压力
Keywords:
bone screws;  osteoporotic fractures;  cancellous bone;  screw damage;  intensity of stress
摘要:
目的:观察两段式拉力螺钉的滑丝率和加压力。方法:招募10位骨科医生和1位独立研究员,在密度为0.08 g·cm-3、0.16 g·cm-3、0.32 g·cm-3的合成松质骨块上进行实验。在相同密度的合成松质骨块上,每位医生分别使用两段式拉力螺钉和AO拉力螺钉各拧紧10次。10位医生在3种密度的合成松质骨块上共操作600次。在医生操作完成后,研究员继续拧紧螺钉,直至加压力明显下降,以确保每次测试所得的加压力曲线均包含上升期、峰值和下降期3个阶段。测量并比较医生与研究员拧紧螺钉时的加压力,判断螺钉是否滑丝。同时,记录医生停止拧紧螺钉时的加压力,以比较两段式拉力螺钉与AO拉力螺钉的加压力。结果:两段式拉力螺钉的滑丝率低于AO拉力螺钉(5.33%,75.67%,χ2=307.923,P=0.000)。不同医生之间,两段式拉力螺钉和AO拉力螺钉的滑丝率均存在差异(χ2=109.366,P=0.000; χ2=17.430,P=0.042)。在密度为0.08 g·cm-3、0.16 g·cm-3、0.32 g·cm-3的合成松质骨块上,两段式拉力螺钉的滑丝率均低于AO拉力螺钉(χ2=126.750,P=0.000; χ2=101.282,P=0.000; χ2=82.353,P=0.000)。不同密度合成松质骨块之间,两段式拉力螺钉的滑丝率存在差异(χ2=6.470,P=0.039),AO拉力螺钉滑丝率的差异无统计学意义(χ2=1.340,P=0.512)。两段式拉力螺钉的整体加压力高于AO拉力螺钉(t=-5.800,P=0.000)。两段式拉力螺钉和AO拉力螺钉的加压力均随合成松质骨块密度的增加而增加(F=2812.63,P=0.000; F=755.193,P=0.000)。结论:相同规格的两段式拉力螺钉的加压力高于AO拉力螺钉,且滑丝率低于AO拉力螺钉。
Abstract:
Objective:To observe the thread stripping rate and pressurization force of a two-segmental lag screw(TSLS).Methods:Ten orthopedic surgeons and an independent investigator were recruited to conduct the experiments on synthetic cancellous bone blocks with densities of 0.08,0.16,and 0.32 g/cm(3),respectively.On the synthetic cancellous bone block with the same density,the TSLS and AO lag screw(AOLS)were tightened 10 times,respectively,by each surgeon.In total,the 10 surgeons operated on the synthetic cancellous bone blocks with three different densities for 600 times.After each surgeon finished the operation,the independent investigator advanced the screw until a remarkable decrease of pressurization force was observed,thereby ensuring the pressurization force curve obtained from each test included the ascending phase,the peak value phase,and the descending phase.The pressurization force applied by each surgeon and the investigator when tightened the screw were measured and compared to determine whether the thread was stripped.Meanwhile,the pressurization forces when the surgeons stopped tightening the screw were recorded to analyze the difference of the pressurization force between TSLS and AOLS.Results:The thread stripping rate of TSLS was lower than that of AOLS(5.33%,75.67%,χ2=307.923,P=0.000).There was difference in the thread stripping rate of TSLS and AOLS among different surgeons(χ2=109.366,P=0.000; χ2=17.430,P=0.042).The thread stripping rate of TSLS was lower than that of AOLS on the synthetic cancellous bone blocks with densities of 0.08,0.16,and 0.32 g/cm(3),respectively(χ2=126.750,P=0.000; χ2=101.282,P=0.000; χ2=82.353,P=0.000).Further comparison revealed that there was difference in the thread stripping rate of TSLS,while,no statistical difference in the thread stripping rate of AOLS among the synthetic cancellous bone blocks with different densities(χ2=6.470,P=0.039; χ2=1.340,P=0.512).The overall pressurization force of TSLS was higher than that of AOLS(t=-5.800,P=0.000).The pressurization force of both TSLS and AOLS increased with the increase in the density of the synthetic cancellous bone blocks(F=2812.63,P=0.000; F=755.193,P=0.000).Conclusion:TSLS has a higher pressurization force and a lower thread stripping rate compared to AOLS with the same specification.

参考文献/References:

[1] 陈金洪.漂膝损伤的诊断与治疗[J].中医正骨,2002,14(1):17-18.
[2] TOULOUPAKIS G,GHIRARDELLI S,THEODORAKIS E,et al.A modified anterolateral swashbuckler approach for distal femoral fractures:description and outcomes[J].Acta Biomed,2022,93(1):e2022005.
[3] ZHANG J,WEI Y,LI G,et al.Interfragmentary lag screw and locking plate combination in simple distal femoral fractures:A finite element analysis[J].Acta Orthop Traumatol Turc,2021,55(1):9-15.
[4] VICENTI G,BIZZOCA D,NAPPI V S,et al.The impact of lag screw in the healing time of distal tibia fractures treated with minimally invasive plate osteosynthesis:A randomized clinical trial[J].Injury,2020,51(Suppl 3):S80-S85.
[5] WICHLAS F,HAYBÄCK G,HOFMANN V,et al.Advancing fracture management:the role of minimally invasive osteosynthesis in orthopedic trauma care[J].Eur J Trauma Emerg Surg,2024,50(5):2331-2344.
[6] COLDING-RASMUSSEN T,SCHWARZENBERG P,HORSTMANN P F,et al.Biomechanical variability and usability of a novel customizable fracture fixation technique[J].Bioengineering(Basel),2023,10(10):1146.
[7] BENEDIKT S,KAISER P,SCHMIDLE G,et al.Lessons learned with the Cobra prosthesis in elderly patients with complex distal radius fractures-a retrospective follow-up study[J].Arch Orthop Trauma Surg,2022,142(2):343-353.
[8] LAMPROPOULOU-ADAMIDOU K,KARAMPINAS P K,CHRONOPOULOS E,et al.Currents of plate osteosynthesis in osteoporotic bone[J].Eur J Orthop Surg Traumatol,2014,24(4):427-433.
[9] 徐达强.一种应用于部分关节骨折的可量化扭力的螺纹型加压装置:201110154601.4[P].2011-10-19.
[10] XU D Q,SUN P D,WANG J,et al.The new shank construct of lag screw improves the maximum compression force for internal fixations:preliminary results[J].Eur Rev Med Pharmacol Sci,2015,19(12):2195-2201.
[11] STOESZ M J,GUSTAFSON P A,PATEL B V,et al.Surgeon perception of cancellous screw fixation[J].J Orthop Trauma,2014,28(1):e1-e7.
中医正骨2025年2月第37卷第2期 J Trad Chin Orthop Trauma,2025,Vol.37,No.2(总113)
(总114)中医正骨2025年2月第37卷第2期 J Trad Chin Orthop Trauma,2025,Vol.37,No.2
[12] FLETCHER J W A,NEUMANN V,WENZEL L,et al.Variations in non-locking screw insertion conditions generate unpredictable changes to achieved fixation tightness and stripping rates[J].Clin Biomech(Bristol),2020,80:105201.
[13] FLETCHER J W A,NEUMANN V,WENZEL L,et al.Screw tightness and stripping rates vary between biomechanical researchers and practicing orthopaedic surgeons[J].J Orthop Surg Res,2021,16(1):642.
[14] FLETCHER J W A,WENZEL L,NEUMANN V,et al.Surgical performance when inserting non-locking screws:a syste-matic review[J].EFORT Open Rev,2020,5(1):26-36.
[15] ADDEVICO F,SOLITRO G F,MORANDI M M.Salvaging pull-out strength in a previously stripped screw site:a comparison of three rescue techniques[J].J Funct Morphol Kinesiol,2021,6(3):71.
[16] ZENG L,WANG Y,HE D,et al.The effectiveness of a self-made modular elastic compression device for patients with a fracture of the tibia and fibula[J].J Orthop Surg Res,2020,15(1):153.
[17] SRINIVASAN A,YOUNG M,AMBROSE C,et al.Maintenance of compression with a positional screw versus compression generated with a lag screw[J].J Orthop Trauma,2019,33(11):564-568.
[18] FENG X,LUO Z,LI Y,et al.Fixation stability comparison of bone screws based on thread design:buttress thread,triangle thread,and square thread[J].BMC Musculoskelet Disord,2022,23(1):820.
[19] USAMI T,TAKADA N,IWATA H,et al.A biomechanical analysis of the effect of hydroxyapatite augmentation for trochanteric femoral fractures[J].Exp Ther Med,2023,25(6):256.
[20] FLETCHER J W A,ZDERIC I,GUEORGUIEV B,et al.Stripping torques in human bone can be reliably predicted prior to screw insertion with optimum tightness being found between 70% and 80% of the maximum[J].Bone Joint Res,2020,9(8):493-500.
[21] REYNOLDS K J,CLEEK T M,MOHTAR A A,et al.Predicting cancellous bone failure during screw insertion[J].J Biomech,2013,46(6):1207-1210.
[22] WILKIE J,JALAL N A,RAUTER G,et al.Segmenting/pre-processing data from bone screw thread-stripping tests[J].Annu Int Conf IEEE Eng Med Biol Soc,2023,2023:1-4.
[23] POILLIOT A,GAY-DUJAK M H,MÜLLER-GERBL M.The quantification of 3D-trabecular architecture of the fourth cervical vertebra using CT osteoabsorptiometry and micro-CT[J].J Orthop Surg Res,2023,18(1):297.
[24] VAHIDI G,FLOOK H,SHERK V,et al.Bone biomechanical properties and tissue-scale bone quality in a genetic mouse model of familial dysautonomia[J].Osteoporos Int,2021,32(11):2335-2346.
[25] XU G,WANG Q,LI Z,et al.Computed tomography osteoabsorptiometry:review of bone density,mechanical strength of material and clinical application[J].Front Bioeng Biotechnol,2023,11:1066709.
[26] 徐达强,孙培栋,赵加力,等.两段式拉力螺钉和AO拉力螺钉加压性能和加压后钉道损伤程度比较[J].中国临床解剖学杂志,2022,40(6):710-713.

相似文献/References:

[1]许兵,叶小雨,王萧枫,等.小管径经皮椎体后凸成形术治疗 骨质疏松性椎体重度压缩骨折[J].中医正骨,2015,27(11):29.
[2]谢小利,李晓程.经皮椎体后凸成形术治疗骨质疏松性椎体 压缩骨折的围手术期护理[J].中医正骨,2015,27(05):79.
[3]郭世明,石玲玲,郭志民,等.手法复位石膏外固定和切开复位钢板内固定治疗 骨质疏松性桡骨远端骨折的比较研究[J].中医正骨,2015,27(04):15.
　GUO Shiming,SHI Lingling,GUO Zhimin,et al.A comparative study of manual reduction and plaster external fixation versus open reduction and plate internal fixation for treatment of osteoporotic distal radius fractures[J].The Journal of Traditional Chinese Orthopedics and Traumatology,2015,27(02):15.
[4]李格,梅伟,刘沛霖,等.骨质疏松性椎体压缩骨折经皮椎体成形术后邻近椎体再骨折的危险因素探讨[J].中医正骨,2016,28(06):18.
　LI Ge,MEI Wei,LIU Peilin,et al.Investigation on risk factors for adjacent vertebral refractures after percutaneous vertebroplasty in patients with osteoporotic vertebral compression fractures[J].The Journal of Traditional Chinese Orthopedics and Traumatology,2016,28(02):18.
[5]徐无忌,刘晓岚.体位复位结合经皮椎体成形术与经皮椎体后凸成形术治疗骨质疏松性椎体压缩骨折的对比研究[J].中医正骨,2016,28(07):20.
　XU Wuji,LIU Xiaolan.Effect of Qianggu Yin(强骨饮,QGY)on bone microstructure in the ovariectomized osteoporosis rats[J].The Journal of Traditional Chinese Orthopedics and Traumatology,2016,28(02):20.
[6]张旭桥,王晓晖,黄光明,等.生骨胶囊在经皮椎体强化术治疗老年骨质疏松性胸腰椎骨折中的应用研究[J].中医正骨,2016,28(11):21.
　ZHANG Xuqiao,WANG Xiaohui,HUANG Guangming,et al.Application of Shenggu Jiaonang(生骨胶囊)to the treatment of osteoporotic thoracolumbar vertebral fractures in the aged who received percutaneous vertebral augmentation[J].The Journal of Traditional Chinese Orthopedics and Traumatology,2016,28(02):21.
[7]张 涛.常规抗骨质疏松疗法联合脉冲射频术和银质针松解术治疗骨质疏松性椎体压缩骨折[J].中医正骨,2017,29(04):74.
[8]牛强卫.手法复位联合经皮椎体成形术和中医骨折三期辨证用药治疗骨质疏松性胸腰椎压缩骨折的临床研究[J].中医正骨,2017,29(04):16.
　NIU Qiangwei.A clinical study of manipulative reduction combined with percutaneous vertebroplasty and oral application of traditional Chinese medicine according ……[J].The Journal of Traditional Chinese Orthopedics and Traumatology,2017,29(02):16.
[9]杨庆贤,曹翠萍,曹哲.常规抗骨质疏松疗法联合腰腹肌训练治疗原发性骨质疏松腰背部疼痛[J].中医正骨,2017,29(06):72.
[10]王建民,李华东,王振东.温针灸结合补阳还五汤口服治疗骨质疏松性椎体压缩骨折经皮椎体后凸成形术后残留痛[J].中医正骨,2017,29(11):69.

备注/Memo

备注/Memo:
基金项目:国家骨科与运动康复临床医学研究中心创新基金资助项目(2021-NCRC-CXJJ-ZH-19)
更新日期/Last Update: 1900-01-01